LED Streetlight Retrofit vs. Replacement: Light Pollution
Dark Sky Ordinances and Policy

LED Streetlight Retrofit vs. Full Fixture Replacement: What Each Choice Means for Light Pollution

By Access Fixtures Lighting Specialists·Dark Sky Ordinances and Policy·November 2026

Converting to LED cuts the power bill. What you convert decides where the light goes. A retrofit kit puts new LEDs inside the old housing. A full replacement swaps the whole luminaire, optics and all. Both save energy. Only one lets you redesign the light that leaves the pole. Leipzig, Germany, just showed how the choice splits in practice. On November 13, 2026, the city passed the halfway mark on its LED conversion: 28,242 of 52,787 light points now run on LED. Of those, 14,509 got a new light source only, and 13,733 got complete new LED luminaires (Leipziger Zeitung, November 13, 2026, citing the City of Leipzig).

Retrofit vs. Replacement: Definitions

Amber LED highway lighting at night
  • LED retrofit kit: an LED light engine and driver installed inside an existing fixture housing. The pole, arm, housing, and often the lens stay in place. The old lamp and ballast come out.
  • Full fixture replacement: a complete new LED luminaire mounted on the existing pole or arm. Housing, optics, driver, and controls are all new.
  • Fully shielded fixture: a fixture built so that no light is emitted above the horizontal plane. Light goes down, onto the street or lot.
  • Correlated color temperature (CCT): the color of white light, measured in kelvin (K). Lower numbers are warmer and more amber. Provo, Utah's 2026 standards, for example, require 3,000K or lower.
  • Light pollution: artificial light that reaches places it is not needed: the sky (skyglow), neighboring property (light trespass), or the eye (glare).

What Leipzig's Conversion Shows

Leipzig's numbers, as reported by the Leipziger Zeitung on November 13, 2026, from the city's announcement:

  • Scale: 28,242 of 52,787 light points now use LED. In 2022 the LED share was just 12.5 percent.
  • Method: 14,509 light-source-only replacements and 13,733 complete new LED luminaires.
  • Energy: connected load fell from 5.068 to 3.597 megawatts. The city reports savings of around 6,301 megawatt-hours and 1.387 million euros in electricity costs a year.
  • Investment: around 2.5 million euros since 2022.
  • Policy: new installations are LED only. Existing systems are retrofitted gradually.
  • Example: on Adolph-Menzel-Straße, ten new steel masts with LED luminaires replaced a 1970s system along 320 metres, for around 100,000 euros. Franz-Mehring-Straße gets 22 new masts with LED in December, for 220,000 euros.

The lesson is not that one method wins. A city with tens of thousands of points uses both. The decision is made fixture by fixture, based on the condition of the housing and what the light needs to do.

Why the Choice Matters for Light Pollution

The optic controls where light lands. A retrofit kit inherits the old housing's geometry. A full replacement lets you specify the distribution from scratch.

LED retrofit kit versus full luminaire replacement Illustration, not to scale. Left: a retrofit kit in an old housing keeps the old optic, so light still goes up and sideways. Right: a new fully shielded luminaire keeps light on the street. LED retrofit kit New light engine inside the old housing Old optic: uplight and sideways spill remain Full replacement New luminaire with new optics and controls New shielded luminaire: light stays on the street
Illustration, not to scale. The optic decides where light lands, and a retrofit keeps the old one.

1. Shielding and uplight

Some older cobra heads and post tops use drop lenses or open globes that send light sideways and up. A retrofit kit inside that housing can keep that pattern. A new fully shielded luminaire puts no light above horizontal.

2. Color temperature

A full replacement lets you choose warm CCT or 590nm amber for wildlife-sensitive sites. A retrofit kit's options are limited to what fits the old housing.

3. Controls

Dimming, photocells, motion sensors, and part-night schedules cut light when no one needs it. Specify them on a new luminaire from the start. Retrofit kits vary; confirm control options before you buy.

Lenses also cost output. Our HPS to LED Conversion Calculator page notes that light loss through prismatic glass is approximately 30%. That is light you pay for and do not get on the ground.

How Ordinances Treat Retrofits and Replacements

Some ordinances draw the line at the fixture. Provo, Utah, is a recent example. Its City Council unanimously approved dark sky lighting standards in late August 2026 (KSL, September 8, 2026):

  • Lamps must be 3,000 Kelvin or lower.
  • Fixtures must be fully shielded so light is directed downward.
  • The rules apply to new installations, major remodels, and full fixture replacements. Existing residential fixtures are exempt, and bulb replacement is allowed.

In practice, a full replacement often triggers the new standard, and a lamp swap often does not. Check your local code before you choose. A lighting specialist can help you read it. See also our report on Provo's standards.

How to Decide: Three Questions

  1. Is the housing sound? Cracked lenses, failed gaskets, and corroded housings point to full replacement. Our wall pack retrofit vs. replacement guide covers the same test for building-mounted fixtures.
  2. Does the light go where it should? If the old fixture lights the sky, the neighbors, or the drivers' eyes, a retrofit keeps the problem. Replace it with a fully shielded fixture.
  3. What does your code require? If a full replacement triggers dark sky standards, plan for shielding, CCT limits, and controls from day one.

Fixtures for Wildlife-Sensitive and Dark Sky Sites

For parking lots, campuses, parks, and coastal properties, the APTA 590nm amber LED area light is IP66 and IK10. A photocell is optional, and a microwave motion sensor can control multiple APTAs.

APTA 590nm amber LED area light at evening
APTA 590nm amber LED area light

Browse the full wildlife friendly LED lighting category for amber area lights, wall packs, and bollards, and our street LED lights. If your streetlights belong to a utility, see what your town can ask for.

Sources: Jan Kaefer, Leipziger Zeitung, November 13, 2026; Cassidy Wixom, “Provo amends outdoor lighting code for dark sky requirements,” KSL, September 8, 2026.

Access Fixtures Solutions

APTA 590nm Amber Area Light

IP66 and IK10, with an optional photocell and microwave motion sensor. See the APTA page.

See the APTA Page →

Street LED Lights

Full-cutoff street lights for towns that own their lights.

Shop Street LED Lights →

Parking Lot Lighting

Shielded parking lot luminaires for full replacements.

Shop Parking Lot Lighting →

Photometric Studies

Model the result of a retrofit or replacement before you buy.

Request a Photometric Study →

Frequently Asked Questions

What is the difference between an LED retrofit and an LED fixture replacement?

An LED retrofit installs a new LED light engine and driver inside the existing fixture housing. A full replacement mounts a complete new LED luminaire, with new housing, optics, driver, and controls. Both cut energy use. Only a full replacement lets you redesign where the light goes.

Does an LED retrofit reduce light pollution?

Not by itself. A retrofit kit keeps the old housing and often the old lens, so light can still spill sideways and upward. Reducing light pollution usually requires a fully shielded fixture, a warm color temperature, and controls that dim or turn off lights when they are not needed.

How many streetlights has Leipzig converted to LED?

As of November 13, 2026, 28,242 of Leipzig's 52,787 light points use LED, according to the Leipziger Zeitung, citing the City of Leipzig. Of those, 14,509 received a new light source only and 13,733 received complete new LED luminaires.

Do dark sky ordinances apply to LED retrofits?

It depends on the ordinance. Provo, Utah's 2026 standards apply to new installations, major remodels, and full fixture replacements, and allow residential bulb replacement. Check your local code, because a full replacement often triggers shielding and color temperature limits that a lamp swap does not.

What color temperature is dark sky friendly?

There is no single number; check your local code. Provo, Utah's 2026 standards require 3,000 Kelvin or lower. Near beaches, wetlands, and other wildlife habitat, 590nm amber LEDs are a common choice.

When should I replace the whole fixture instead of retrofitting?

Replace the whole fixture when the housing is cracked or corroded, when the old optic sends light into the sky or onto neighbors, or when your local code requires shielding or color limits on new work. Retrofit when the housing is sound and the existing distribution already puts light where it belongs.

How do I know where the light will land before I buy?

Request a photometric study. An Access Fixtures lighting engineer models your site with the proposed fixtures and shows light levels and spill at the property line before installation. Call 800-468-9925.

Get a Photometric Study Before You Convert

Retrofit or replace, the right answer depends on your site. Send us your site plan, pole locations, and current fixtures. A lighting specialist will recommend fixtures, and a lighting engineer will model the result. Call 800-468-9925 or request a photometric study online.

800-468-9925